LDL Cholesterol Calculator

Enter total cholesterol, HDL, and triglycerides to calculate LDL cholesterol using the Friedewald and Sampson equations, plus non-HDL cholesterol.

LDL cholesterol is commonly calculated using the Friedewald equation: LDL = TC − HDL − TG/5 (in mg/dL). For example, with TC 200, HDL 50, and TG 150 mg/dL, Friedewald LDL is 200 − 50 − 150/5 = 120 mg/dL. The Sampson/NIH equation gives a more accurate result of 123 mg/dL for the same values, especially when triglycerides are elevated.

Free, runs in your browser. Nothing you enter is uploaded.

How to use it

  1. Enter your total cholesterol (TC) in mg/dL.
  2. Enter your HDL cholesterol in mg/dL.
  3. Enter your triglycerides (TG) in mg/dL.
  4. View calculated LDL by Friedewald and Sampson equations, non-HDL cholesterol, and risk category.

What you enter

What you get

Formula

Friedewald: LDL = TC − HDL − TG/5 (mg/dL) | Sampson (NIH): LDL = TC/0.948 − HDL/0.971 − (TG/8.56 + TG×NonHDL/2140 − TG²/16100) − 9.44 | Non-HDL = TC − HDL

The Friedewald equation estimates LDL cholesterol as LDL = TC − HDL − TG/5, where TC is total cholesterol, HDL is high-density lipoprotein cholesterol, and TG is triglycerides, all in mg/dL. This formula works because very low-density lipoprotein (VLDL) cholesterol is approximated as triglycerides divided by 5, based on the typical ratio of triglyceride to cholesterol in VLDL particles. The equation subtracts HDL and estimated VLDL from total cholesterol to leave LDL. It is valid only when triglycerides are below 400 mg/dL. At low LDL levels or high triglycerides, it tends to underestimate true LDL.

The Sampson/NIH equation 2 is a more complex formula: LDL = TC/0.948 − HDL/0.971 − (TG/8.56 + TG × NonHDL/2140 − TG²/16100) − 9.44. Here, NonHDL is non-HDL cholesterol, calculated as TC − HDL. This equation was developed using a large dataset and direct LDL measurements. It adjusts for the changing relationship between triglycerides and VLDL cholesterol across a wider range of values. It is valid for triglycerides up to 800 mg/dL and provides more accurate LDL estimates, especially when triglycerides are high or LDL is low.

Non-HDL cholesterol is simply TC minus HDL. It represents all cholesterol carried by atherogenic lipoproteins, including LDL, VLDL, and lipoprotein(a). Many guidelines recommend a non-HDL target below 130 mg/dL for people at risk. Non-HDL does not require a calculation that assumes a fixed triglyceride-to-VLDL ratio, so it is reliable even when triglycerides are very high.

To use these formulas, enter values in mg/dL. If your lab reports in mmol/L, multiply cholesterol values by 38.67 and triglycerides by 88.57 to convert. The calculator returns LDL by both methods and non-HDL. Results are interpreted using NCEP ATP III categories: less than 100 mg/dL is optimal, 100 to 129 near optimal, 130 to 159 borderline high, 160 to 189 high, and 190 or above very high. An LDL of 190 mg/dL or higher warrants statin therapy regardless of other risk factors, according to the 2018 AHA/ACC guideline.

Fasting is not required for most routine lipid panels. The Martin/Hopkins method is another accurate approach that uses a 180-cell factor table instead of a fixed divisor, but it is not included in this calculator.

Worked example

Input: TC 200, HDL 50, TG 150 mg/dL

Result: Friedewald 120 mg/dL; Sampson 123 mg/dL; non-HDL 150 mg/dL

Near optimal (100–129 mg/dL).

Questions

What is the formula for calculating LDL cholesterol?

The most common formula is the Friedewald equation: LDL = total cholesterol − HDL − triglycerides/5, with all values in mg/dL. This equation estimates LDL by subtracting HDL and an estimate of VLDL cholesterol from total cholesterol. It is valid only when triglycerides are below 400 mg/dL.

When should I use the Sampson equation instead of Friedewald?

Use the Sampson equation when triglycerides are between 400 and 800 mg/dL, or when LDL is very low. The Friedewald equation underestimates LDL at high triglycerides or low LDL levels. The Sampson equation is more accurate across a wider range and is valid up to 800 mg/dL triglycerides.

What is a normal LDL cholesterol level?

According to NCEP ATP III guidelines, an optimal LDL level is below 100 mg/dL. Levels of 100 to 129 mg/dL are near optimal, 130 to 159 mg/dL are borderline high, 160 to 189 mg/dL are high, and 190 mg/dL or above is very high. An LDL of 190 mg/dL or higher warrants statin therapy regardless of other risk factors.

How do I convert cholesterol from mmol/L to mg/dL?

To convert total cholesterol or HDL cholesterol from mmol/L to mg/dL, multiply by 38.67. For triglycerides, multiply by 88.57. For example, a total cholesterol of 5.2 mmol/L equals about 201 mg/dL.

What is non-HDL cholesterol and why is it used?

Non-HDL cholesterol is total cholesterol minus HDL cholesterol. It includes all atherogenic lipoproteins such as LDL, VLDL, and lipoprotein(a). Many guidelines recommend a non-HDL target below 130 mg/dL. It is reliable even when triglycerides are very high, unlike calculated LDL.

Do I need to fast before a cholesterol test?

Fasting is not required for most routine lipid panels. Non-fasting samples provide reliable results for total cholesterol, HDL, and non-HDL cholesterol. Triglycerides may be slightly higher after eating. If triglycerides are very high, ask about a fasting repeat or a directly measured LDL.

Limitations

References

More Health & Wellness

All free tools · By Dr. Zubair Khalid, DVM, MS, PhD.